WDW-XD Series Computer Control Macromolecule Pitch Waterproof Material Testing Machine

1 Introduction

1) test and research with waterproof roll in building: bitumen waterproof roll, high polymer modified bitumen waterproof roll, macromclecule waterproof roll, elastomer modified bitumen waterproof roll, pre-paving/wet-pre-paving waterproofing roll, bitumen based and polyester based waterproof roll, single side bonding, double side bonding, Ⅰ/Ⅱtype waterproof roll and other mechanics property.

2) Test and research with petroleum and bitumen waterproof roll, bitumen compounding based flexible waterproof roll, glass fiber, based / cloth based/ paper based rolling material, self adhesive rubber asphalt waterproof rolling material, self adhesive polymer/asphalt waterproof rolling material, plastomer asphalt water proof rolling material, EPDM water proof rolling material, polythylene based rolling material for mechanical property.

3) test and research with natural rubber, composite rubber, solid rubber(dry glue), emulsus rubber(latex), universal composite rubber, half universal composite rubber, special usage composite rubber, special composite rubber, medical and biological rubber, foam rubber(foaming rubber/ micro hole rubber), butadiene styrene rubber, EPDM, NBR, HNBR, IIR, butadiene rubber, isoprene rubber, silicone rubber, EPR, neoprene, hard rubber, soft rubber, vulcanizate, compounding rubber, 1 type , 1A type, 2 type, 3 type, 4 type and pant shaped sample, right angle sample, crescent shaped sample.

4) test and research for mechanical property with plastic thin film, general plastic, engineering plastic, special plastic, strengthen plastic, foam plastic, thermoset plastic, thermoplasticity plastic, hydrocarbon, mould pressing plastic, lamination plastic, newly medcial plastic, newly bulletproof plastic, newly bioloyical plastic, 1B type, 2 type, 4 type, 5 type sample.

5) test and research with hard and half hard thermoplasticity mould plastic material, hard and half thermosetting board and layer compression board, felt, textile, roving without twisting, chopped strand, mixed fiber strengened material, fiber strengthened thermosetting and thermoplasticity compounding material.

6) asphalt macromolecule material test for tensile, tearing(pin rod method), Max. peak value of tensile force, second peak value of tensile force, elongation of Max. peak, elongation of second peak, peeling strength of seam, tensile strength, elongation of breaking, stress of specified elongation, elongation of specified stress, stress at yielding point, elongation at yielding point, permanent deforamtion of breaking.

7) test with rubber and plastic: tensile strength, yielding tensile strength, tensile strength of breaking, tearing strength, tensile strain of yielding, tensile strain at breaking, tensile modulus of elasticity, Poisson’s ratio, elongation of breaking, drawing stress-strain curve.

8) test and research with material specimen of thin board, belt, foil, oblate, wire, stick, proximate matter, tube, thin sheet, square, round, rectangular, round ring, tubulation, proportional sample, non-proportional sample, peeling belt, cross section of rectangule and round.

9) test and research with textile, food, medcine, cosmetics, biological material, flexible material, elasticity material, foam material, electricity part, thin metal, wire, fine wire, firber, adhesive.

2 Standard

1) ISO 23529-2010 Rubber- General procedures for preparing and conditioning test pieces for physical test methods

2) BS ISO 37-2011 Rubber, vulcanized or thermoplastic. Determination of tensile stress-strain properties.

3) BS EN 13707-2013 Flexible sheets for waterproofing. Reinforced bitumen sheet for roof waterproofing. Definitions and characteristics.

4) BS EN 13956-2012 Flexible sheet for waterproofing. Plastic and rubber sheets for roof waterproofing. Definitions and characteristics.

5) BS EN ISO 16012:2015 Thermal insulation for building. Reflective insulation products. Determination of the declared thermal performance.

6) BS EN ISO 527 – 1 - 2012 Plastics. Determination of tensile properties. General principles.

7) ISO 527-2:2012 Plastic-- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics.

8) DIN EN ISO 527-3 Plastics -- Determination of tensile properties -- Part 3: Test conditions for films and sheets

9) ISO 527-4 Plastic -- Determination of tensile properties -- Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites

10) ASTM D 7078/D 7078M-05 Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method

11) ISO 14130 Fibre - reinforced plastic composites -- Determination of apparent interlaminar shear strength by short-beam method.

3 Specification