首頁 >> 試驗機案例 >> 5kN熱塑性彈性體材料拉伸試驗Vulcanized Rubber and Thermoplastic Elastomers Tensile
5kN熱塑性彈性體材料拉伸試驗測試拉伸強度、屈服強度、斷裂強度、撕裂強度、剝離強度、粘合強度、拉伸應力、屈服應力、斷裂應力、拉伸應變、屈服應變、斷裂應變、拉伸彈性模量、泊松比、斷裂伸長率、繪制荷載-位移曲線、應力-應變曲線。
5kN熱塑性彈性體材料拉伸試驗機；5kN硫化橡膠拉伸試驗機；5kN熱塑性材料拉伸試驗機；5kN彈性體薄膜拉伸試驗機；HRJ Tests；5kN彈性體片材拉伸試驗機；5kN高分子材料拉伸試驗機；5kN汽車橡膠件拉伸試驗機；5kN汽車塑料件拉伸試驗機；5kN熱塑性橡膠拉伸試驗機；5kN剛性基板粘合強度測定；90°剝離法試驗；POE拉伸測試；TPO薄膜和片材拉伸測試；HRJ Tests；5kN氟彈性體材料拉伸試驗機；QB/T5349-2018車用聚烯烴彈性體（TPO）薄膜和片材；NB/T10200-2019晶體矽太陽電池組件用聚烯烴彈性體（POE）封裝絕緣膠膜；JB/T13593-2018電氣用氟彈性體熱收縮管；90°Peel Method；ASTM D412-2006a(2013)；HRJ Tests；ISO 37-2011；ISO 815；ISO 7743；ISO 34-1；DIN ISO 813-2011；ISO 18064-2014；ASTM D5538-2013；GMW 15812-2016；GMW 15813-2017；SMTC 5 320 024；SMTC 5 400 239；KS M 16012:2015；90°Peel Fixture；ASTM D 7078；ISO 14130；JIS A6021；ISO 11469；ISO 4928；ISO 6118；ISO 1817；HRJ Tests；ISO 23936-2；IEC 60684-3-233；HG/T5113-2016；HG/T4903-2016；90°Peel Adhesion Test；SH/T1610-2011；SH/T1812-2017；JT/T1089-2016；QB/T5351-2018；QC/T797-2008；GB/T34903.2-2017；GB/T29334-2012；HRJ Tests；GB/T2951.21-2008；GB/T26528-2011；
Vulcanized Rubber Tensile Tester；Thermoplastic Elastomers Tensile Tester；Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomersmdash Tension；HRJ Tests；Rubber vulcanized or thermoplastic-Determination of tensile stress-strain properties；Rubber At ambient or elevated temperatures；Determination of compression stress-strain properties；Rubber Determination of tear strength；Trouser angle and crescent test pieces；Determination of adhesion to a rigid substrate；Thermoplastic elastomers-Nomenclature and abbreviated terms；Standard Practice for Thermoplastic Elastomersmdash Terminology and Abbreviations；Thermoplastic Elastomers Polyolefinic Fully Cross；Thermo plastic elastomers(tpe) material requirements；Rubber permanent deformation test method；Thermoplastic elastomers based on the waste rubber and plastic；Styrene butadiene styrene(SBS) modified bitumen for waterproof；Polyolefin elastomer（TPO） film and sheet for vehicle；Material identification & marking of automotive plastic rubber & thermoplastic elastomer parts；
All materials and products covered by these test methods must withstand tensile forces for adequate performance in certain applications；HRJ Tests；These test methods allow for the measurement of such tensile properties；tensile properties alone may not directly relate to the total end use performance of the product because of the wide range of potential performance requirements in actual use；Tensile properties depend both on the material and the conditions of test (extension rate, temperature, humidity, specimen geometry, pretest conditioning, etc)；therefore materials should be compared only when tested under the same conditions；HRJ Tests；Temperature and rate of extension may have substantial effects on tensile properties and therefore should be controlled；These effects will vary depending on the type of material being tested；Tensile set represents residual deformation which is partly permanent and partly recoverable after stretching and retraction；the periods of extension and recovery (and other conditions of test) must be controlled to obtain comparable results；HRJ Tests；These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers；low elongation materials test；Material Tester；Various Testing Machine；Laboratory Equipment；HRJ Material Tester；Asia Tests；World Material Tester；Tester Service Center；Tester Fittings Supply Center；Design Manufacture Center；Special Test Accessories；
|
